lift trucks equipment - radiator tanks and parts - Bolt on Top Tanks - equipment
Header: 21.00" x 6.75"
28 Bolt Holes
Top Tank:
This tank has a height of 3.50"
2.00" diameter hose connection 3.00" from the edge of the tank to the center of the hose connection
The hose connection is 3.00" long. 1.37" hole to accommodate a filler neck, 6.50" from the edge of the tank.
Bottom Tank:
This tank is identical to the top tank, except without the filler neck hole.
Note: This set comes with 4 washer bars 21.00" long with 12 bolt holes, and 4 washer bars 4.25" long with 2 bolt holes.
Header: 42.00" x 6.50"
48 Bolt Holes
Paling Unit Complete Set
Top Tank:
This tank has a 2.50" diameter hose connection 13.00" from the edge of the tank to the center of the hose connection (4.00" long)
2 - 1/4" NPT flanges located just above the de-airation baffle 9.00" and 12.00" from the edge of the tank
1/4" NPT flange on the top of the tank for a vent tube
Each end of the tank has a 9/16" diameter hole for lifting
Bottom Tank:
This tank has a 2.75" diameter hose connection 11.00" from the edge of the tank to the center of the hose connection (angled 15 degrees upwards, 4.75" long)
1/2" NPT drain flange 7.12" from the edge of the tank
2 - 11/16" diameter holes at 36.50" centers for mounting
The outer ends of the tank slant inwards to allow for mounting holes.
Side Frames:
Plain Frames 33.75" in height.
Header: 29.00" x 6.50"
38 Bolt Holes
Top Tank:
This tank has a 1.75" diameter hose connection centered in the tank
1.75" diameter pipe to accommodate a filler neck on the top of the tank
Bottom Tank:
This tank has a 2.00" diameter hose connection 8.00" from the edge of the tank to the center of the hose connection
1/4" NPT flange for the drain 6.00" from the edge of the tank
Side Frames:
22.75" long
NOTE : Set comes with four 21.00" long washer bars with 11 bolt holes.
Header: 47.00" x 7.00"
52 Bolt Holes
Top Tank:
This tank has a 2.50" diameter hose connection
3/4" NPT fitting for a bypass hose
1/2" NPT flange on the end of the tank
and one on the back for a sight glass
1/4" NPT flange on the front and one on the back for a sensor
1.75" diameter hole on the top at one end for a filler neck
Bottom Tank:
This tank has a 2.50" diameter hose connection
1/4" NPT flange for a drain cock
2 - 3/4" thick mounting plates with 1/2" NC threaded holes in the center
Side Frames:
10 - 5/16" threaded nuts, five along the grill side and five along the fan side
Mounting block at each end
2 - 1/2" NC threaded holes
Each horseshoe flange has eight 3/8" diameter holes to accommodate 5/16" bolts.
Header: 37.00" x 6.50"
46 Bolt Holes
Woodchipper Complete Set
Top Tank:
This tank has a 2 1/2" diameter hose connection
1/4" NPT flange
1 3/4" diameter hole for a filler neck
Bottom Tank:
This tank has a 2 1/2" diameter hose connection
1/4" NPT flange for a drain cock
This set comes with a fan shroud 42.00" high, 37.00" wide, 2.87" deep, with a 31.00" diameter hole
4 washer bars also supplied 27.87" long with 14 bolt holes.
Header: 29.50" x 6.50"
38 Bolt Holes
Paling Complete Set
Top Tank:
This tank has a 2.50" diameter hose connection 2.75" from the edge of the tank to the center of the hose connection
1/4" NPT flange 11.25" from the edge of the tank
1/2" NPT flange 4.00" from the edge of the tank for a sight glass
1.75" diameter hole on the top center of the tank for a truck fill neck
1/4" NPT flange 3.00" from the edge of the tank for an expansion tube
1/2" flange in the end of the tank for a sight glass
Bottom Tank:
This tank has a 1/4" NPT flange 2 1/2" from the edge of the tank for a drain
2 3/4" diameter hose connection 2 3/4" from the edge of the tank to the center of the hose connection
Frames:
Frames are 34" long with 9 bolt holes per flange.
Note : tank set comes with washer bars.
Header: 23.50" x 6.68"
32 Bolt Holes
These tanks are used for core testing, and have a 1/4" NPT flange on top to allow for a pressure line.
Header: 37.50" x 6.50"
42 Bolt Holes
2 - 2.25" diameter hose connections
1/2" NPT flange for a sight glass
1/4" NPT flange for a sensor
A hole in the top for a filler neck
Header: 42.37" x 7.87"
52 Bolt Holes
Top and Bottom Tanks:
2.50" NPT coupling
1/4" NPT flange
Side Frames:
These frames have flanges that are 7.87" wide x 6.00" deep
2 - 1/2" NC threaded holes to accommodate lifting hooks
Note: this set is supplied with four washer bars 30.37" long with 15 bolt holes.
Header: 31.00" x 8.50"
This is a blank tank with large brackets roughed in on the top. Customer to finish the bolt holes, etc, to accommodate the application.
Header: 68.00" x 7.00"
76 Bolt Holes
Top Tank:
This tank has a 4.00" NPT coupling
A hole for a filler neck in the top center of the tank
4 - 1/2" NC threaded holes at each end of the tank to attach the side frames
Bottom Tank:
This tank has a 4.00" NPT coupling
3/4" NPT coupling for a drain
4 - 1/2" NC threaded holes at each end of the tank to attach the side frames
Side Frames:
These frames have eight holes to accommodate 1/2" bolts to attach to the tanks
A hole to accommodate a lifting hook
2 holes in the foot plate to attach to a mounting block
Series of 3/8" diameter holes
Note: this set comes supplied with four washer bars 66.00" long with 33 bolt holes, and four washer bars 7.00" long with 5 bolt holes.
Header: 50.00" x 7.50"
64 Bolt Holes
Top Tank:
This tank has a 2.25" diameter hose connection
1.00" diameter bypass connection
1/4" NPT flanges for sensors etc
1/2" NPT flange on the grill side for a sight glass
2 - 1/2" NC threaded holes on each end for lifting
Bottom Tank:
This tank has a 2.50" diameter hose connection
1/2" NPT flange
2 - 10 plate oil coolers with 18.00" centers
2 - 1/2" NC threaded holes for mounting
Side Frames:
5 - 5/16" threaded holes along each side for mounting the shroud
Block with two 1/2" NC threaded holes for mounting
Note: this set is supplied with four long washer bars.
Header: 52.25" x 8.50"
60 Bolt Holes
Top Tank:
This tank has two 2.50" diameter hose connections
2 - 1/2" NPT flanges
4 - mounting blocks ( 2 on top and 2 on the ends)
Bottom Tank:
This tank has a 4.00" diameter hose connection
2 mounting pads
2 mounting blocks
1/2" NPT flange
Side Frames:
These frames are 58.50" long, with an angle running along one edge
The angle has six 7/16" diameter holes @ 9.50" centers
Note: this tank set is supplies with an assortment of twelve washer bars.
Header: 37.93" x 7.50"
48 Bolt Holes
Stelco Water Truck Tanks and Frames
Top Tank:
This tank has a 2.00" diameter hose connection 11.00" from the edge of the tank to the center of the hose connection (angled @ 90 degrees)
Hose connection has a 1/4" NPT flange for a drain
2 - 3/4" NC bolts @ 32.00" centers
1/4" NPT flange 9.00" from the edge of the tank
Frames:
29.00" tall with a 9 bolt flange
4 - 3/8" NC nuts along the edge of the frame for mounting the fan shroud
Header: 29.50" X 6.25"
40 Bolt Holes
Top Tank:
This tank has a 1.75" diameter hose connection
1/4" NPT flange for an expansion fitting
Bottom Tank:
This tank has a 2.00" diameter hose connection
1/2" NPT flange to accommodate a hose barb
1/4" NPT flange for a drain
Side Frames:
These frames are 26.00" tall
Each flange has eight bolt holes
Note: this complete tank set is supplied with four washer bars 19.37" long with 10 bolt holes.
Header: 27.50" x 8.75"
36 Bolt Holes
This top tank has an overall height of 5.00"
2.50" NPT nipple hose connection is on the left side
1/2" NPT coupling for sensor nearby
1/2" NPT sight glass flange
The 2.50" studs at each end are 3.00" long
Top center of the tank has a truck-sized filler neck hole.
Header: 39.00" x 7.00"
58 Bolt Holes
Top Tank:
This tank has two 1.25" NPT couplings facing towards the engine
Bottom Tank:
This tank has two 1.25" NPT couplings facing towards the ground
This set comes with four long washer bars and four short washer bars. Tanks are made from 3/16" thick #304 stainless steel.
Header: 49.00" x 8.00"
64 Bolt Holes
Top Tank:
This tank has a 2.25" diameter hose connection
1.00" diameter fill line
2 - 1/2" NC threaded nuts
2 - 1/4" NPT flanges
A hole for a filler neck
Bottom Tank:
This tank has a 2.50" diameter hose connection
1/2" NC threaded hole at each end for mounting
2 - 1/2" NPT flanges (one for a drain on the bottom, and one facing the engine)
2 - 10 plate oil coolers with 18.00" centers
Side Frames:
These frames have eleven 3/8" diameter clearance holes in the flange
5 - 5/16" NC threaded nuts
33.62" long
Note: this rad set is supplied with four washer bars 37.00" long with 21 bolt holes
Header: 35.25" x 54.87"
40 Bolt Holes
Top tank:
This tank has two 1.62" diameter hose connections separated by a baffle
1/4" NPT coupling for an expansion fitting
1/2" NPT flange for a fill line
A mounting ear on each end to attach frames
Bottom Tank:
This tank has a 1/4" NPT coupling for an expansion fitting
1/2" NPT flange for a fill line
A mounting ear on each end to attach frames
Side Frames:
These frames have eight slotted mounting holes
6 - 3/8" diameter holes to attach to another complete unit (OEM #HV004 or set #081409A)
Holes to allow access to the 1/4" NPT fittings
Note: this set comes supplied with four washer bars 7.50" long with 5 bolt holes, and four washer bars 33.12" long with 16 bolt holes.
Header: 35.25" x 7.50"
42 Bolt Holes
Hover Craft Complete Bolt on Set
Top Tank:
This tank has two 2.50" diameter hose connections 12.37" long
1/2" NPT flange for a fill line
1/4" NPT coupling for an expansion line
A mounting ear on each end to attach side frames
A baffle separates the two hose connections
Bottom Tank:
This tank has a 1/2" NPT flange for a fill line
1/4" NPT coupling for an expansion fitting
Side Frames:
These frames have eight slotted mounting holes
6 - 3/8" diameter holes to attach a second complete unit (OEM #HV003 or set #081409B)
Holes to access the 1/4" NPT fittings on the tanks
Note: this set comes supplied with four washer bars 7.50" long with 5 bolt holes, and four washer bars 33.12" long with 16 bolt holes.
Header: 40.50" x 6.00"
56 Bolt Holes
Top Tank:
This tank has two 2.00" diameter hose connections 2.75" long and separated by a baffle
1/4" NPT flange for an expansion fitting
Threaded mounting block on each end for attaching side frames
Bottom Tank:
This tank has a 1/4" NPT fitting for a drain cock
Threaded mounting blocks on each end of the tank
Side Frames:
These frames have 4 - 1/2" wide by 1.25" long slotted holes for bolting side frames to the tank
This set comes with four long washer bars and four short washer bars.
Header: 22.00" x 5.00"
30 Bolt Holes
Top Tank:
This tank has 2 - 3/4" NPT couplings separated by a baffle
1/4" NPT flange for an expansion plug
Threaded mounting blocks on each end for attaching side frames
Bottom Tank:
This tank has a 1/4" NPT flange for a drain cock
Threaded mounting blocks on each end for attaching side frames
Side Frames:
These frames have 4 - 1/2" x 1.25" long slotted holes for bolting on the side frames to the tanks
This set comes with four long washer bars and four short washer bars
