truck - radiator tanks and parts - Bolt on Top Tanks - freightliner

Two openings of 2.00" O.D. 90 degree elbows facing down
One 1.00" O.D. hose connection
One 1/8" N.P.T. fitting on side
One bolt-on type filler at the center on the top front corner
Built-in baffle

Two openings of 2.00" O.D. pipe straight out
One 1.00" O.D. hose connection
One 1/8" N.P.T. fitting on side
One bolt-on type filler at the center on the top front corner
Built-in baffle

Two openin gs of 2.25" O.D. pipe straight out
One 1.00" O.D. hose connection
One 1/8" N.P.T. fitting on side
One bolt-on type filler at the center on the top front corner
Built-in baffle

One opening of 2.00" O.D. pipe on a 45 degree bend facing down
One 1.00" O.D. hose connection
One 1/8" N.P.T. fitting on side
One bolt-on type filler at the top front corner
Built-in baffle

One opening of 2.50" O.D. 90 degree facing down and towards center at a 45 degree angle
One 1.00" O.D. hose connection
One 1/8" N.P.T. fitting on side
One bolt-on type filler at the center on the top front corner
Built-in baffle

One opening of 2.50" O.D. 90 degree elbow facing down and towards center at a 45 degree angle
One 1.00" O.D. hose connection
One 1/8" N.P.T. fitting on side
One bolt-on type filler at the center on the top from corner
Built-in baffle.

Two openings of 2.25" O.D. straight out. One 1.00" O.D. hose connection
One 1/8" N.P.T. fitting on side
One bolt-on type filler at the center of the slanted top (see picture)
Built-in baffle

Two openings of 2.25" O.D. 90 degree elbows facing down and out slightly to each end of tank
One 1.00" O.D. hose connection
Two 1/8" N.P.T. fittings, one on side and one in top corner (driver's side)
One bolt on type filler at the center of the slanted top
Built-in baffle

Two openings of 2.50" O.D. pipes, one coming out on a 20 degree angle and one coming out on a 45 degree angle, each facing towards the center of the tank
One 1.00" O.D. hose connection
One 1/8" N.P.T. fitting on side
One bolt-on type filler at the center of the top front corner|
Built-in baffle

One opening for 2.00" O.D. pipe on a 45 degree bend facing down
One 1.00" O.D. hose connection
One 1/8" N.P.T. fitting on side
One bolt-on type filler a the center on the top front corner
Built-in baffle

One opening for 2.00" O.D. pipe on a 45 degree bend facing down
One 1.0" O.D. hose connection
One 1/8" N.P.T. fitting on side
One bolt-on type filler at the center on the top
Built-in baffle

Two openings of 2.25" O.D. pipe straight out
One 1" O.D. hose connection
One 1/8" N.P.T. fitting on side
One bolt-on type filler at the center on the top front corner
Built-in baffle

Two openings of 2.50" O.D. pipe straight out
One 1.00" O.D. hose connection
One 1/8" N.P.T. fitting on side
One bolt-on type filler at the center on the top front corner
Built-in baffle

Two openings, one is a 2.25" O.D. 90 degree elbow facing down (passenger side), one is a 2.25" O.D. pipe straight out (driver's side)
One 1.00" O.D. hose connection
One 1/8" N.P.T. fitting on side
One 1/4" fitting on lower corner passenger side
One bolt-on type filler at the center on the top front corner
Built in baffle

One opening (on driver's side) of 3.00" O.D. 90 degree elbow facing opposite end of tank (see picture)
One 1/8" N.P.T. fitting on side
One bolt-on type filler at the center of the top front corner
Built-in baffle

One opening of 2.25" O.D. pipe coming out on approximately a 30 degree angle towards center of tank. One 1" O.D. hose connection
One 1/8" N.P.T. fitting on side
One bolt-on type filler at the center on the top front corner
Built-in baffle

One opening of 2.50" O.D. pipe coming out on approximately a 30 degree angle towards centre of tank. One 1.00" O.D. hose connection. One 1/8" N.P.T. fitting on side
One bolt-on type filler at the center on the top front corner
Built-in baffle

One opening of 2.25" O.D. pipe coming out on approximately 30 degree angle towards the center of the tank
One 1.00 " O.D. hose connection One 1/8" N.P.T. fitting on side
One bolt-on type filler at the center of the slanted top
Built-in baffle

One opening of 2.50" O.D. pipe coming out on approximately 30 degree angle towards the center of the tank
One 1.00 " O.D. hose connection
One 1/8" N.P.T. fitting on side
One bolt-on type filler at the center of the slanted top
Built-in baffle

Low-flow tank with "rounded" header One 1.00" O.D. hose connection facing engine
One 3/8" O.D. hose connection on passenger's side also facing engine
Two bolt-on type flanges on top of tank
Built-in baffle
One 1/4" N.P.T. flange in baffle for check valve
NOTE: Check valve installed

Low flow tank with "rounded" header has one 1.00" O.D. hose connection on driver's side lower section facing passenger side (on 75 degree angle)
One 1.00" O.D. hose connection on passenger's side of center facing passenger side and slightly down. One 3/8" O.D. hose connection on passenger side facing engine
Two bolt-on type flanges on top of tank
One 1/4" N.P.T. fitting in built-in baffle for check valve
Top driver's side of tank is cut lower to accommodate air to air cooler
NOTE: Check valve installed

Low flow tank with "rounded" header has one 1.00" O.D. hose connection facing engine
One 3/8" O.D. hose connection on passenger's side also facing engine
Two bolt-on type flanges on top of tank
One 1/4" N.P.T. flange in built-in baffle for check valve
Top driver's side of tank is cut lower to accommodate air to air cooler
NOTE: Check valve installed

Tank has "rounded" header
One 1.00" O.D. hose connection on approximately a 90 degree angle facing passenger side
One 2.50" O.D. hose connection on passenger's side facing down on approximately a 20 degree angle
One 3/8" O.D. hose connection facing engine
Built-in baffle with aeration tube

Tank has "rounded" header
One 1.00" O.D. hose connection on approximately a 90 degree angle facing passenger's side
One 2.50" O.D. hose connection on passenger's side facing down on approximately a 20 degree angle
One 3/8" O.D. hose connection facing engine
Built-in baffle with aeration tube. Top driver's side of tank cut lower to accommodate air to air cooler

Tank has "rounded" header
One 1.00" O.D. hose connection on approximately a 90 degree angle facing passenger's side
Two 2.50" O.D. hose connections facing down on approximately a 20 degree angle
One 3/8" O.D. hose connection facing engine
Built-in baffle with aeration tube

Tank has "rounded" header
One 1.00" O.D. hose connection on approximately a 90 degree angle facing passenger's side. Two 2.50" O.D. hose connections facing down on approximately a 20 degree angle
One 3/8" O.D. hose connection facing engine
Built-in baffle with aeration tube. Top driver's side of tank is cut lower to accommodate an air to air cooler

Tank has "rounded" header
One 1.00" O.D. hose connection on approximately a 90 degree angle facing passenger's side
One 2.50" O.D. hose connection on passenger's side facing straght back
One 3/8" O.D. hose connection facing engine
One 3/8" N.P.T flange
Built-in baffle with aeration tube
Top driver's side of tank cut lower to accommodate air to air cooler

This blank tank has rounded corners. There is a 1/4" NPT flange on each end. Note: matches with tank #FR 459LF

This low flow tank has a "rounded" header
There is a 1.25" diameter hose connection facing straight out
1/4" NPT flange on the end

This low flow tank has a "rounded" header
There is a 1.00" diameter hose connection facing straight out
1/4" NPT flange on the end

This tank has a "rounded" header
3.00" diameter hose connection
1/4" NPT flange on the end
Note: matches tank #FR 458

This tank has a "rounded" header
A 1.25" diameter hose connection facing out on approximately a 70 degree angle
A 1/4" NPT flange in the center

This tank has "rounded" header
There is a 2.50" diameter hose connection
1/4" NPT flange on the end
Note: matches tank #FR456

This low flow tank has a "rounded" header
1.25" diameter hose connection and a 1.00" diameter hose connection straight to engine
1/4" NPT flange on each end
A baffle in the center splits the tank top to bottom
Note: matches tank #FR452LF

Top Tank :
This tank has a pair of 2.37" diameter hose connections
Mounting bracket at the front center of the tank
1/4" NPT flange for an expansion fitting
Bottom Tank :
This tank has a pair of 1/2" NC bolts 3.00" long @ 30.00" centers for mounting
3.00" diameter hose connection
1.75" diameter hose connection
3/8" NPT plug for draining
Side Frames :
These frames have five 3/8" NC threaded holes on the back for mounting the frames
Ten 5/16" threaded holes along the sides for mounting the shroud
Note: this set comes supplied with two 3/8" threaded tie rods 50.00" in length, and four washer bars that fit between the side frames

Inlet Tank :
This tank has a 2.50" diameter hose connection
1/4" NPT flange on each end of the tank
Outlet Tank :
This tank has a 3.00" diameter hose connection
1/4" NPT flange on each end of the tank
1/4" NPT x 3/8" diameter 90o hose barb is provided.