truck - radiator tanks and parts - Bolt on Top Tanks - international

This top tank is essentially a #627 modified for a low flow application
One new pipe connection
Blank plate
This tank is fitted with a check valve.

Two bolt on type flanges with two 3/8" N.C. threaded holes in each
One 3/8" N.P.T.
One 1/4" N.P.T. facing engine
One 1/2" N.P.T. fitting on grille side One flange connection on baffle with two 5/16" N.C. threaded holes
One hole for filler neck on top front edge

One 2.25" O.D. hose connection in center facing engine
Two 1/8" N.P.T. fittings on top
One hole for filler neck on top
One 3/8" N.P.T. fitting on passenger end of tank
One 1.00" O.D. hose connection out baffle on passenger side - angled to passengers end of tank
Fifteen 5/16" N.C. threaded holes in baffle.

One 1/4" N.P.T. fitting facing engine One 3/8" N.P.T. on passenger’s side (end)
One 1/4" N.P.T. fitting on driver’s side (end)
One 3/4" and two 1/4" N.P.T. fittings on top
One hole on top for filler neck (NOTE: One 3/4" N.P.T. fitting goes through the tank.)
One 1.00" hose connection out baffle on passenger’s side angled to passengers end of tank
Fifteen 5/16" N.C. threaded holes in baffle

Two bolt on type flanges with two 3/8" N.C. threaded holes in each One 1/4" and one 1/2" N.P.T. fitting facing engine
One 5/8" O.D. hose connection on lower passenger side facing engine One hole on top slope for filler neck One bolt on type flange on front driver’s side
One 1/2" N.P.T. fitting on front driver’s side
One bolt on type flange in baffle

Two bolt-on type connections with two 3/8" N.C. threads
One bolt-on type filler with four 5/16" N.C. threads
One 3/4" N.P.T. fitting
One 1/2" N.P.T. fitting
Two 3/8" N.P.T. fittings
One 1/4" N.P.T. fitting
Built-in baffle

Two flanges with two 3/8" N.C. threaded holes in each
Two 3/8" N.P.T. fittings
Two round brackets
One bracket on top
One 1.75" hole on top for filler neck One flange in built-in baffle with two 5/16" N.C. threads
One bar on built-in baffle with five 5/16" N.C. threaded holes.

Twenty 5/16" N.C. threads in built-in baffle
One 2.25" O.D. hose connection on driver’s side
One 1.00" O.D. hose connection on passenger’s side in built-in baffle One 1.75" pipe on front for filler neck
Three 1/4" N.P.T. fittings
Two brackets fitted on top of tank

Tank has twenty 5/16" N.C. threaded holes in built-in baffle
Two 2.25" O.D. hose connections
One 1.00" O.D. hose connection out baffle on passenger’s side
Three 1/4" N.P.T. fittings on driver’s side
One 1.75" pipe on front for filler neck
Two brackets on top of tank

Sixteen 5/16" N.C. threaded holes in built-in baffle
One 2.25" hose connection on driver’s side
One 1.00" O.D. hose connection on passenger’s side
One 1.75" pipe on front for filler neck
Three 1/4" N.P.T. fittings

Low flow tank has sixteen 5/16" N.C. threaded holes in baffle
Five 1/4" N.P.T. fittings on driver’s side - four facing engine and one on top
One 1.00" O.D. hose connection out baffle on passenger’s side
One 1 3/4" pipe on front for filler neck

Two 1.50" O.D. 90 degree elbows facing down and slightly out on each end
One 1.00" O.D. hose connection
One 1/2" N.P.T fitting
One 3/8" N.P.T. fitting
Fifteen 5/16" N.C. threaded holes in built-in baffle
One 1.25" hole for filler neck on top passenger side

One 2.50" O.D. hose connection at center
One 3/4" N.P.T. fitting
One 1/2" N.P.T. fitting
One 1/8" N.P.T. fitting
Fifteen 5/16" N.C. threaded holes in built-in baffle
One 1.25" hole for filler neck on top driver’s side

One 2.50" O.D. hose connection in center
One 1.00" O.D. 90 degree hose connection on passenger’s side
One 1/8" N.P.T. fitting
One 1.25" hole on top passenger’s side for filler neck
Built-in baffle

This tank has a 2.75" diameter hose connection that bends 90 degree on approximately a 45 degree angle
One 3/8" NPT flange on each end of the tank

This tank has a 2.75" diameter hose connection that bends 90 degree on approximately a 45 degree angle
One 3/8" NPT flange on each end of the tank
7 plate oil cooler with 18.00" centers (718PC)
Note: this tank is the same as tank #IN637, except for the oil cooler

This tank has a 2.75" diameter hose connection 10.50" in from end
Two 3/8" NPT fittings (one on each end)
Note: this tank is the same as tank #IN637, but with cutouts on each end to accommodate a charged air cooler (CAC).

This low flow tank has a baffle in the center that splits the tank between the two hose connections
One hose connection is 1.00" diameter and the other hose connection is 1.25" diameter
One 3/8" NPT flange on each end of the tank

This tank has a 2.50" diameter hose connection with a 45 degree elbow that points upwards
Note: if you need this tank with an oil cooler, order tank #IN6381

This tank has a 2.50" diameter hose connection with a 45 degree elbow that points upward
A 7 plate oil cooler with fittings at 18.00" centers (718PC)
Note: this tank is identical to tank #IN638, except for the oil cooler.

Low flow tank
Mate to #IN637LF
Tank has no fittings or hose connections

Two flange connections with two 3/8" N.C. threaded holes in each
Two 1/4" N.P.T fittings
One 3/8" N.P.T. fittings
One 1/2" N.P.T. fitting on front facing engine
One 1.75" filler hole on top driver’s side
One 1/2" N.P.T. fitting on driver’s side
One flange on bottom with two 5/16" N.C. threaded holes
NOTE: Matches tank #IN642

Twenty seven 5/16" N.C. threaded holes in built-in baffle
One flange connection with two 5/16" N.C. threaded holes in baffle
Two flange connection with two 3/8" N.C. threaded holes in each, facing engine
Four 1/4" N.P.T. fittings
One 3/8" N.P.T fitting
One 1/2" N.P.T. fitting
One 1.75" hole on top for filler neck NOTE: Matches tank #IN645

This tank has a 2.50" diameter hose connection that bends @ 90 degree and angles slightly upwards
One 1/4" NPT flange on the end

This tank has a 2.50" diameter hose connection straight out to the engine 10.37" in from end to center
One 1/4" NPT coupling welded in end of tank on approximately a 45 degree angle

This tank has a 2.50" diameter hose connection that bends at 90 degree
One 1/2" NPT flange on end of the tank

This basic blank tank has 1/4" NPT flange on the shallow side of the tank. Note: matches tank #IN643-2LF

This tank has a 1.25" diameter hose connection straight out towards the engine
A 1.00" diameter hose connection on a 90 degree angle facing the engine
A baffle in the tank approx. 1/2" off center that splits the tank left to right
One 1/4" NPT flange on the shallow end of the tank
Note: this tank is a mirror image of tank #IN643LF

This tank has a 2.50" diameter hose connection facing the engine
Two 1/4" NPT flanges - one on rise of tank and one at the shallow end of the tank
Note: this tank is the mirror image of tank #IN643 ( 2 .50" hose connection on other side) with one more fitting at end.

This tank has a 2.50" diameter hose connection 6.00" in from the end of the tank straight out towards the engine
One 1/4" NPT flange on each end
The tank is only 1.50" deep, and has two corners of the header cut on 45 degree angle

This tank has a 2.50" diameter hose connection, 9.00" in from the end of the tank straight out towards the engine
One 1/4" NPT flange on each end This tank is only 1.50" deep, and has two corners of the header cut on a 45 degree angle

This driver’s side blank tank has a 1/4" NPT flange on each end
The tank is 1.50" deep and the header corners on grille side are cut on a 45 degree angle

This passenger side tank has a 1.00" diameter hose connection near the top
A 1.25" diameter hose connection near the bottom
A baffle divides the tank width-wise at the center
One 1/4" NPT flange in each end
Two corners of the header are cut on 45 degree angle.

This tank has a 2.50" diameter hose connection, 6.25" in from end, coming out on approximately a 45 degree angle and turned on approximately a 30 degree angle
One 1/4" NPT flange on the opposite end

This tank has a 2.50" diameter hose connection 8.25" from the end, coming out on approximately a 60 degree angle and turned on approximately a 30 degree angle There is a 1/4" NPT flange on each end

Top Tank :
This tank has a 2.75" diameter hose connection 3.00" long
1/4" NPT flange
1.25" diameter hole in to top center of the tank for a filler neck
Bottom Tank :
This tank has a 2.75" diameter hose connection 3.00" long
Two 1/4" NPT flanges for drains
Side Frames :
These frames have 11 bolt holes
A bracket for mounting with a 5/8" diameter hole
Note: this rad set is supplied with four washer bars 17.25" long with 11 bolt holes.

Top Tank :
This tank has a 2.75" diameter hose connection 3.00" long
1/4" NPT flange
1.25" diameter hole in the top center of the tank for a filler neck
Bottom Tank :
This tank has a 2.75" diameter hose connection 3.00" long that points downwards
1/4" NPT flange for a drain cock
Side Frames :
These frames have 11 bolt holes
Mounting bracket with a 5/8" diameter hole
A bracket along the fan edge to mount the shroud with a slotted hole on top for bolt clearance
Note: this rad set is supplied with four washer bars 17.25" long with 11 bolt holes, and two CAC mounting brackets.